Axial angular contact ball bearing Double-row steel ground 23806-104007534
- Support of high radial and axial loads
- High axial load rating due to the 60° pressure angle
- High rigidity
Unidade de venda
€355.70
+ o ICMS alemão
Adicionado ao seu carrinho de compras
Denominação
Rolamento de esferas de contato angular axial
Versão 1
de duas filas
Material
do corpo
básico
aço
Superfície
Corpo básico
retificado
Material
dos componentes
buna N
B=Largura
34 -0,25
D1=Diâmetro externo
75-0,01
D=Diâmetro interno
40-0,005
KZZ.=Abreviatura
4075-2RS
Capacidade de
carga dinâmica
N
43000
Capacidade de
carga estática
N
101000
D2
57
Diâmetro exterior
Limites de tolerância
μm
0-10
Folga do rolamento
radial
pré-tensionado
Furo
Limites de tolerância
μm
0-5
Largura
Limites de tolerância
μm
0-250
R min.
0,3
R1 min.
0,6
Rigidez de inclinação
Nm/mrad
550
Rotação
limite
Rpm
1800
Torque de
inércia
Kg cm²
2,260
Torque de aperto
porca da ranhura de precisão
Nm
55
Torque de atrito do rolamento
Nm
0,70
UNSPSC Code
31171512
curso linear
μm
2,5
rigidez
axial
N/μm
1000
α
60°
~ CONFLICT MINERALS 3TG status
not yet identified
~ CONFLICT MINERALS procurement
DRC conflict-free
~ CP65 substance 2 cancer
soots, tars, and mineral oils
~ PFAS free?
not yet identified
~ REACH SVHC-free?
yes
~ RoHS conformity
yes, without exemption
~ TSCA 6(H) conformity
yes
Descrição
Material
Steel housing.
Nitrile rubber seal.
Nitrile rubber seal.
Version
Ground edges.
Note
Preloaded high-accuracy bearings with a 60° thrust angle. The bearings accept both radial and axial forces from both directions. Due to their preload, the angular contact ball bearings provide a high level of stiffness, excellent concentricity, precise tool positioning and repeatability.
The integrated low-friction seal effectively keeps dirt away from the bearing, thereby ensuring excellent operating safety and a long service life.
The bearing friction coefficient Mrl is a reference value.
The moment of inertia corresponds to that of the rotating inner ring.
The limiting speeds are applicable after grease is applied.
The integrated low-friction seal effectively keeps dirt away from the bearing, thereby ensuring excellent operating safety and a long service life.
The bearing friction coefficient Mrl is a reference value.
The moment of inertia corresponds to that of the rotating inner ring.
The limiting speeds are applicable after grease is applied.
Technical Data
All bearings are supplied ready for mounting with lubricating grease type KE2P-35 acc. to DIN 51825.
Housing and shaft tolerances correspond to roundness tolerance class IT2 and perpendicularity tolerance class IT4.
Housing and shaft tolerances correspond to roundness tolerance class IT2 and perpendicularity tolerance class IT4.
Application
For thread drive bearing.
Temperature range
-30 °C to +120 °C.
Assembly
Precision slotted nuts must be used for mounting the threaded spindles.
To compensate for any material settling during assembly, tighten the slotted nuts using 2x tightening torque, loosen slightly and then tighten using the prescribed tightening torque.
To compensate for any material settling during assembly, tighten the slotted nuts using 2x tightening torque, loosen slightly and then tighten using the prescribed tightening torque.
Nota importante sobre o descarregamento de modelos CAD
Para descarregar os nossos modelos CAD, é necessário iniciar sessão primeiro. Se ainda não criou uma conta, por favor registe-se em "A minha conta" (lado direito do ecrã) e siga as instruções.
Outros clientes também compraram
